Earth Electrode Resistance: How to Calculate It (IS 3043 Formulas + Worked Examples)

Earth electrode resistance is the resistance between an earthing electrode and the general mass of the earth. It depends on three things only: the resistivity of the soil, the shape and size of the electrode, and how deep it sits. Because the relationship is predictable, you can estimate it on paper before anyone digs a pit — which is exactly what IS 3043 (Code of Practice for Earthing) lets you do.

This guide gives the IS 3043 formulas for the three common electrode shapes, works each one through with real numbers, and shows which design change actually moves the result.

Start with soil resistivity (ρ)

Every formula below is directly proportional to soil resistivity, ρ, measured in ohm-metres (Ω·m). Double the resistivity and you double the electrode resistance — no electrode choice will undo that. So the first step is always to measure ρ on site, normally with the Wenner four-pin method, at several spacings and ideally in the dry season. Typical ranges are wide: moist clay can be well under 100 Ω·m while dry sand or rock can run into thousands.

All the worked examples below use ρ = 100 Ω·m so the numbers are easy to scale. For your site, multiply by (your ρ ÷ 100).

Formula 1 — vertical rod or pipe electrode

IS 3043 gives the resistance of a single vertical rod or pipe as:

R = (100 ρ / 2π l) × logₑ(4 l / d)

R = resistance (Ω)
ρ = soil resistivity (Ω·m)
l = length of rod (cm)
d = diameter of rod (cm)

Worked example: a 3 m rod (l = 300 cm) of 16 mm diameter (d = 1.6 cm) in 100 Ω·m soil.
100 × 100 / (2π × 300) = 5.31; logₑ(4 × 300 / 1.6) = logₑ(750) = 6.62; so R ≈ 35 Ω.

That is a single rod in average soil — well above the value most installations need. Which is why the next section matters more than the formula itself.

Length beats diameter: what actually lowers the number

Running the same formula with one variable changed at a time (ρ = 100 Ω·m):

RodCalculated RChange vs 3 m × 16 mm
1.5 m × 16 mm≈ 63 Ω+79%
3 m × 16 mm (baseline)≈ 35 Ω—
3 m × 32 mm (double the diameter)≈ 31 Ω−11%
3 m, 100 mm effective diameter (rod in a conductive backfill column)≈ 25 Ω−28%
6 m × 16 mm (double the length)≈ 19 Ω−45%

Three practical conclusions follow:

  • Depth is the most powerful lever. Doubling length cuts resistance by roughly 45%; doubling diameter cuts it by about 11%. Paying for a fatter rod is rarely the answer — driving deeper, or coupling sectional rods, usually is. Deeper soil is also more likely to stay moist through summer.
  • Backfill works by enlarging the electrode. A low-resistivity compound packed around the rod behaves like a much larger-diameter electrode and also lowers the resistivity right where current density is highest. That is the principle behind earthing backfill compound and chemical earthing electrodes.
  • In high-resistivity soil no single electrode will get you there. You need multiple electrodes, a longer horizontal conductor, or both.

Formula 2 — plate electrode

R = (ρ / 4) × √(π / A)

A = area of ONE face of the plate (m²)

Worked example: a 600 × 600 mm plate (A = 0.36 m²) in 100 Ω·m soil: 25 × √(3.1416 / 0.36) = 25 × 2.95 ≈ 74 Ω. That is roughly double the 3 m rod above, with far more excavation and far more metal. It is one reason plate earthing has largely given way to driven rods and chemical electrodes — see types of earthing electrodes for the full comparison.

Formula 3 — horizontal strip or round conductor

R = (100 ρ / 2π l) × logₑ(2 l² / w t)

l = length of strip (cm)
w = width of strip (cm) — or twice the diameter for a round conductor
t = depth of burial (cm)

Worked example: a 10 m run of 25 mm strip (l = 1000 cm, w = 2.5 cm) buried at 0.5 m (t = 50 cm) in 100 Ω·m soil: 15.9 × logₑ(2,000,000 / 125) = 15.9 × 9.68 ≈ 15 Ω. Long horizontal conductors are very effective where rock stops you driving deep — the same logic as rod length: more contact with soil, lower resistance.

Multiple electrodes in parallel

Two identical rods do not give half the resistance of one. Each rod sits inside the other’s “resistance area”, so the combined value is always higher than R ÷ n. The practical rules:

  • Space electrodes at least one rod length apart, and preferably twice the rod length. Closer than that and the second rod adds little.
  • Expect diminishing returns: each additional rod contributes less than the one before it. IS 3043 provides multiplying factors for rods in a line or ring — use them rather than simple division.
  • Connect them with a buried conductor, which itself contributes (Formula 3), and give each electrode a test link so each can still be measured on its own.

Calculation is the design; measurement is the proof

Formulas assume uniform soil. Real sites are layered, seasonal and full of buried services, so the calculated figure is a design estimate, not a guarantee. Always measure after installation with the fall-of-potential method — our step-by-step guide on how to check earthing resistance covers the procedure — and compare against the target for the application in earth resistance value: what is acceptable.

Frequently asked questions

What is the formula for earth electrode resistance?

For a vertical rod, IS 3043 gives R = (100ρ / 2πl) × logₑ(4l/d), with ρ in Ω·m and rod length l and diameter d in centimetres. Plates and strips have their own formulas, shown above.

What is the resistance of a 3 m earthing rod?

In 100 Ω·m soil, a 3 m × 16 mm rod calculates to about 35 Ω. The result scales directly with soil resistivity: in 50 Ω·m soil it would be about 17.5 Ω; in 300 Ω·m, about 105 Ω.

Does a thicker earthing rod give lower resistance?

Only slightly. Doubling the diameter lowers resistance by roughly 11%; doubling the length lowers it by roughly 45%. Choose diameter for mechanical strength and corrosion life, and length for resistance.

How does backfill compound reduce earth resistance?

It surrounds the electrode with low-resistivity material, which effectively increases the electrode’s diameter and improves contact with the soil. It helps most in dry, sandy or rocky ground where contact is poor.

Why is my measured value different from the calculated one?

Formulas assume uniform soil. Layered soil, seasonal moisture, nearby buried metal and test-probe placement all shift the real reading. Measure in the dry season for the worst case.

Designing an earthing system for a difficult site? Ashlok has manufactured chemical earthing electrodes, copper bonded earthing rods and backfill compound since 1999 — share your soil resistivity and target value and we will help size the system.